No products in the cart.
TNY277PN Price in Pakistan
Showing all 14 results
- Components, IC, Power, Voltage Converters
MC34063API MC34063A 34063A Step Up Down Inverting Switching IC
Components, IC, Power, Voltage ConvertersMC34063API MC34063A 34063A Step Up Down Inverting Switching IC
The MC34063A Series is a monolithic control circuit containing the primary functions required for DC−to−DC converters. These devices consist of an internal temperature compensated reference, comparator, controlled duty cycle oscillator with an active current limit circuit, driver and high current output switch.
SKU: n/a - Components, IC
RDA5815M 5815M QFN-20 Signal IC
- RDA5815M is the fourth-generation satellite receiver radio frequency front-end chip that RDA rolled out in 2012.
- It is compatible with all DVB-S, DVB-S2&ABS satellite modes.
- The chip features superior performance, ultra-wide dynamic range (100dB), minimum noise coefficient (MAX 5.5) and good linearity.
SKU: n/a - Components, IC, Power, Voltage Converters
TNY277PN Power Managment IC
- Manufacturer: Power Integrations
- Product Category: AC/DC Converters
- Mounting Style: Through Hole
- Package/Case: DIP-7
- Output Voltage: 12 V
- Output Power: 18 W
- Input / Supply Voltage – Min: 85 VAC
- Input / Supply Voltage – Max: 265 VAC
- Switching Frequency: 132 kHz
- Duty Cycle – Max: 65 %
SKU: n/a - Components, IC, Power, Voltage Converters
SD6830 PWM PFM Power Management IC
- SD6830 is current mode PWM+PFM controller with built-in high-voltage MOSFET used for SMPS.
- It features low standby power and low start current. In standby mode, the circuit enters burst mode to reduce the standby power dissipation.
- The switch frequency is 25~67KHz decided by the load with jitter frequency for low EMI.
- Built-in peak current compensation circuit makes the limit peak current stable even with different input AC voltage.
- Maximum peak current compensation during power-on reduces pressure on transformer to avoid saturation, the peak current compensation will decrease for balance after power-on.
- Limit output current can be adjusted through the resistor connected to CS
SKU: n/a - Components, IC, Power, Voltage Converters
SD6835 PWM PFM Power Management IC
- SD6835 is current mode PWM+PFM controller used for SMPS with built-in high-voltage MOSFET and external sense resistor.
- It features low standby power and low start current. In standby mode, the circuit enters burst mode to reduce the standby power dissipation.
- The switch frequency is 25~67KHz decided by the load with jitter frequency for low EMI.
SKU: n/a - Components, IC, Power, Voltage Converters
THX203H High Performance Switch Mode Power Controller IC
- PWM controller of high-performance current mode is specially designed for AC/DC transformer with high performance and price ratio
- Which supplies continuous output power of 12W within the range of wide-voltage between 85V and 265V,
- The output power of peak value can be up to 18W.
- The combination of optimized reasonable circuit design and bipolar facture technology with high performance and price ratio economizes the whole cost ultimately.
- The power controller can be applied to the typical flyback circuit topology so as to form a simple AC/DC transformer
SKU: n/a - IC, Components, Power, Voltage Converters
AP8012 OFF Line SMPS Primary Switcher Power Management IC
- The AP8012 combines a dedicated current mode PWM controller with a high voltage power MOSFET on the same silicon chip.
- 9v to 38v wide range VCC voltage
- Fixed 60KHz switching frequency
- Automatic skip cycle mode in low load condition.
- Over temperature, over current and over voltage protection
SKU: n/a - Components, IC, Power, Voltage Converters
SD6834 PWM PFM Power Management IC
- SD6834 is current mode PWM+PFM controller with built-in high-voltage MOSFET used for SMPS.
- It features low standby power and low start current. In standby mode, the circuit enters burst mode to reduce the standby power dissipation.
- The switch frequency is 25~67KHz decided by the load with jitter frequency for low EMI.
- Built-in peak current compensation circuit makes the limit peak current stable even with different input AC voltage.
- Maximum peak current compensation during power-on reduces pressure on transformer to avoid saturation, the peak current compensation will decrease for balance after power-on.
- Limit output current can be adjusted through the resistor connected to CS
SKU: n/a
