Modules Price in Pakistan
Showing 49–72 of 172 results
- Arduino, Arduino Components, Modules, Programmers, Tools
USB to Serial TTL Converter CH340G
- This is a USB 2.0 to TTL UART CH340/CH340G Module Serial Converter.
- Designed to be used for USB to TTL
- Built-in USB to RS232 Transfer chip.
- USB specification 2.0 compliant with full-speed 12Mbps.
- Standard USB type A male and TTL 5pin connector.
- Event character support Line break transmission.
- USB suspend states supported via SUSPEND pins.
- Temperature Range: -40degree to +85degree.
- Supports Windows 98SE, 2000, XP, Vista, Window7,8,10 Mac OS 9, Mac OS X Linux 2.40.
SKU: n/a - Modules, Power, Relays
XH-M603 Charge Controller Protection Module With LED Display
XH-M603 is a Charging Control Module 12-24V with Protection from Overcharging
- XH-M603 is ideal solution for Solar Panel & Battery
- Connect your Solar Panel or Charger on In+ & In-
- Connect Battery on BAT+ & BAT- (Lithium or Lead Acid)
- This Module protects your battery from Overcharging & Overheating
- It will extend the life of your battery
- This Module can operate on either 12V Single Battery or 24V Dual Battery
SKU: n/a - Modules, Power, Voltage Converters
0.9V 3V 5V to 5V 600MA USB Output Charger Module
- Input Voltage: 1-5V
- Output Voltage: 5.1-5.2V
- Output Current: Rated 600MA
- Efficiency:: Up to 96%
- Works with all types of Lipo & Lithium batteries for example 18650 bl5c bl5b
- Charge cellphone or power up your USB Gadgets
SKU: n/a - Arduino, Arduino Components, Modules, Programmers
USBASP USBISP Programmer for ATMEL AVR ATMega ATTiny
Arduino, Arduino Components, Modules, ProgrammersUSBASP USBISP Programmer for ATMEL AVR ATMega ATTiny
- Directly connected to USB port of PC
- Easy interfacing with Microcontroller
- Onboard ATMEGA8A chip for programming
- onboard 500ma overcurrent protection fuse
- 3.3v & 5v supply for target
- Support All AVR ASP chips
- Autospeed, automatic adaptive serial speed control.
- Reserved MOSI, MISO, RST, SCK, VCC, GND 6PIN Interface
SKU: n/a - Arduino Components, Modules, Power, Relays, Robotics
LED Display Automatic Cycle Delay Real Time Clock RTC Control Relay
Arduino Components, Modules, Power, Relays, RoboticsLED Display Automatic Cycle Delay Real Time Clock RTC Control Relay
- Operating voltage: 5.0V ~ 60V
- Support MicroUSB 5.0V Power Supply
- Trigger Source: Active-high (3.0V-24V),
- Output Capability: You can control the DC 30VDC 5A or 220VAC 10A device.
- Quiescent Current: 20mA; Operating Current: 50mA
- Life: more than 10 million times; Working temperature: -40-85
- This Module can be used to specifically Turn On / Turn Off an Electrical appliance on Specific Time for the specific duration
- This is Advanced Cyclic Timer Relay Module with Timer Clock function as well
SKU: n/a - Arduino, Arduino Components, Modules, Programmers
CP2102 USB to Serial TTL Converter Micro USB
- Origional CP2102 IC Chip onboard
- Micro USB 6PIN TTL UART CP2102 Module
- On board Fuse for Short Circuit Protection
- DTR Pin for Auto Programming
- Designed to be used for USB to TTL Serial
- Built-in USB to RS232 Transfer chip
- Micro USB to TTL 6pin connector.
- 6pins for 3.3V, RST, TXD, RXD, GND & +5V.
- Temperature Range: -40degree to +85degree.
- Support: Windows, Linux & MAC
SKU: n/a - Arduino Components, Modules, Power, Tools
Digital Panel Voltmeter 0.36 LED Display 0-100V DC
- Type: 3-Wire Car Digital Voltmeter
- Material: Plastic
- Operating Voltage: DC 2.5-30V
- Operating Current: <20mA
- Measure Voltage: DC 0-100V
- Minimum Resolution: 0.1V / 0.01V
- Display: Red color, three digit, 0.36″
- Refresh Rate: About 200mS / times
SKU: n/a - Modules, Power, Relays
XH-M131 12V LDR Photoresistor Light Control Relay Module
- Light threshold can be adjusted by potentiometer to set the relay start
- Input: 12V DC
- Load capacity: 10A / AC 250V or DC up to 30V
- Size: 30MM*53MM
- Uses
- This can be used to control the light automatically by detecting the day light.
- This Module can be used to kill the WAPDA Power supply to UPS in Solar Power Environment
SKU: n/a - Charge Controller, Modules, Power, Relays
XH-M601 Battery Charging Protection Module
- Model: XH-M601
- Power Supply: 13.8V-14.8V
- Relay closing voltage: 12.4V
- Relay off voltage: 14.8V
- Voltage error:±0.1V
- Voltage detection: DC voltmeter
- Charging type: 12V battery
- Potentiometer adjustment: RP1 RP2 (carefully adjusted)
SKU: n/a - Modules, Power, Voltage Converters
LTC1871 High Power 100W Digital Display Stepup Boost Module
The boost module uses advanced microcontroller and U.S. imports boost controller, it eliminates the need for a current sense resistor by utilizing the power mosfet’s on-resistance, thereby maximizing efficiency, up to 96.4%. Imported high-power low-resistance mos transistor, heavy current and high efficiency schottky, wider and thicker PCB traces, is a guarantee of high-power and low temperature rise. When the input and output voltage is greater than 20V, the module up to 128W output power.
SKU: n/a - Arduino, Arduino Components, Modules, Power, Robotics
NE555 PWM Pulse Signal Generator
- Used as a square wave signal generator
- offer the square wave signal for the use of the experimental development.
- Used to produce driving stepper motor drives, offer the square wave signal.
- Adjustable pulse for the use of MCU.
- Generate pulse with adjustable frequency & duty cycle.
SKU: n/a - Modules, Power, Voltage Converters
XL4016 DC-DC 200W 8A Step Down Buck Converter
- Input voltage: DC 4-38V
- Output voltage: DC 1.25-36V
- Maximum current: 8A
- Maximum power: 200W
- Conversion efficiency: 95%
- Working Temperature: -45~+85℃
- Size: 6×3.7cm/2.36×1.46inch
- Voltage Regulating Mode: PWM Modulation
- Switching Frequency: 180KHz
SKU: n/a - Arduino, Arduino Components, Modules, Sensors
HC-SR501 PIR Infrared Motion Sensor Detector Module
- Color: White + Green
- Dimension: 3.2cm x 2.4cm x 1.8cm (approx)
- Infrared sensor with control circuit board
- The sensitivity and holding time can be adjusted
- Working Voltage Range: DC 4.5V- 20V
- Current drain:<60uA
SKU: n/a - Arduino, Arduino Components, Modules, Sensors
Infrared Reflective Obstacle Avoidance Sensor
- Sensor module output port OUT can be directly connected with the microcontroller IO port.
- Can also directly drive a 5V relay; Connection: VCC-VCC; GND-GND; OUT-IO
- The Comparator with LM393, Stable.
- Can be used 3.3V-5V DC power supply module. When the power is turned on, the red power indicator light;
- VCC external 3.3V-5V voltage (can be directly connected with the 5v microcontroller or 3.3v single-chip)
- GND external GND
- OUT small board digital output interface (0 and 1)
SKU: n/a - Modules, Power, Voltage Converters
DC-DC 8V-35V To 5V 8A Step Down Power Charger Module
- DC-DC 8V35V To 5V 8A StepDown Power Charger Module
- 4 USB Ports Output
- 4 Independant Controller IC for Each USB Port
- Conveniently use with any 12v to 24v adapter
- For Multiple USB power supply needs
- Power Hungry Devices Tablets, Pads, Cell Phones.
SKU: n/a - Modules, Power, Relays, Sensors
XH-W3001 Digital Thermostat Temperature Control
- Temperature measurement range: – 50 ~ 110
- Temperature control range: – 50 ~ 110
- Operating Voltage: 12v DC | 220v AC
- Control Voltage: 1v – 250v
- Load: Upto 1500W
- Temperature measuring accuracy: plus or minus 0.2 degree
- Temperature control precision: plus or minus 0.1 degree
- Measuring input: NTC10K L = 1 meters waterproof probe
- Input power: according to the classification of choice
- Output power: according to the classification of choice
- Appearance size: 60 * 45 * 31 mm
SKU: n/a - Battery, Charge Controller, Modules, Power, Relays
XH-M602 Charge Controller Protection Module With LED Display
Battery, Charge Controller, Modules, Power, RelaysXH-M602 Charge Controller Protection Module With LED Display
- Input Voltage: AC 220
- Inpu Current: 220v & 10A Max (2250 Watt)
- Battery Voltage: 3.7V – 120V
- Display Accuracy:0.1V
- Control Accuracy:0.1V
- Output Type: AC Out for Charger
- Voltage Tolerance:±0.1V
SKU: n/a - Arduino, Arduino Components, Modules, Sensors
SW-420 Normally Closed Vibration Sensor Module
- The company produced normally closed type vibration sensor SW-420
- The comparator output, signal clean, good waveform, driving ability is strong, for more than 15 ma
- The working voltage of 3.3V to 5V
- Output form: digital switch output (0 and 1)
- Has a fixed bolt hole, convenient installation
- Small board PCB size: 3.2cm x 1.4cm
- Use the LM393 wide voltage comparator
SKU: n/a - Modules, Power, Voltage Converters
XL4016 DC-DC 200W 8A Step Down Buck Converter Potentiometer
- Input voltage: DC 4-38V
- Output voltage: DC 1.25-36V
- Maximum current: 8A
- Maximum power: 200W
- Conversion efficiency: 95%
- Working Temperature: -45~+85℃
- Size: 6×3.7cm/2.36×1.46inch
- Voltage Regulating Mode: PWM Modulation
- Switching Frequency: 180KHz
SKU: n/a