No products in the cart.
Modules Price in Pakistan
Showing 25–48 of 171 results
- Modules, Power, Voltage Converters
XL7015 5V-80V Input DC-DC Converter Step-Down Module
- PINOUTS
- VIN: Input voltage (5 v – 80v)
- The GND: Input Voltage GND
- The VOUT: Output Voltage (5 v – 20 v)
- The GND: Output Voltage GND
- 5 v to 80v Wide Input Voltage Range
- Shut off built-in Overheating Protection
- Output Short Circuit Protection
- Over Current Protection
- Good linear with load regulation
- The board size: 16 mm * 44 mm
SKU: n/a - PINOUTS
- Modules, Sensors
XH-M452 LED Digital Thermostat Temperature Humidity Control Dual Output
- Digital Thermostat, Temperature Control Module can be used to control the Temperature & Humidity, Set the specific Temperature & Humidity you want to maintain.
- Power Supply :DC 12V
- Temperature Measurement Range:-40~120℃
- Humidity Range：0~100%RH
- Control Precision：0.1℃ 0.1%RH
- Test Probe：Integrated Sensor (Temperature & Humidity)
- Output: 2 Relays 10A
- Size:65*55*28mm
SKU: n/a - Arduino, Arduino Components, Modules, Programmer Components, Programmers
MAX3232 RS232 to TTL Serial Port Converter Module DB9 Connector
Arduino, Arduino Components, Modules, Programmer Components, ProgrammersMAX3232 RS232 to TTL Serial Port Converter Module DB9 Connector
- Communications chip: Domestic MAX3232
- Operating voltage: 3.3V-5.5V
- It is widely used in radio modification, phone flash , GPS ,vehicle detection,DVD flash, hard disk repair set-top box upgrade
- It can be used to program STC MCU, NXP MCU, Renesas MCU,STM32 MCU, N+-2EC MCU Communication
- chip: domestic MAX3232
- Port: TX RX VCC GND
SKU: n/a - Arduino, Arduino Components, GSM, Modules, Wireless
M590E GPRS GSM Module Dual Band DIY
M590E GPRS GSM Module Dual Band (UnSoldered)
- This is UnSoldered (do it yourself) KIT
- Chip: M590E
- Voltage: 5v
- Best for SMS GPRS
- Support networks: GSM 900 & GSM 1800 Network
- Module size: 50mm*50mm
- TTL serial port for serial port, you can link directly to the microcontroller. No need MAX232
- Power module automatically boot on home network
- Onboard status LED.
SKU: n/a - Arduino Components, Modules, Power, Tools
Digital Voltmeter Panel LED Display 3-30V DC
- Feature:Reverse Connect Protection
- Range: DC3.0-30V (No need aditional power)
- Display: Three 0.56” LED digital tube
- Display color: red
- Refresh rate: about 500mS / times
- Input: DC voltage (<2 times the range)
- Resolution: 1% +1 digit
- Power Supply: DC3.0-30V (with the input common-line)
- Operating temperature: -10°c~ 65°c
SKU: n/a - Arduino, Arduino Components, Display, Modules
I2C Interface Plate for LCD Display Module
- I2C Address: 0x27
- Supply voltage: 5V
- Dimension: 41.5mm*19mm*15.3mm
- The Backlight and contrast is adjusted by Potentiometer
- Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable
- Compatible for 1602 16×2 2004 20×4 20×2 Character LCD Display
SKU: n/a - Modules, Power, Voltage Converters
0.9V ~ 5V to 5V 600MA USB Output Charger Module
- The onboard subminiature PFM control DC/DC boost controller chip
- Any input 0.9 V ~ 5 V dc voltage, stable output 5 V dc voltage
- The onboard USB female, can be directly to the USB interface equipment power supply
- The onboard the input voltage indicator light
- PCB size: 34 x16.2 (mm) (mm)
- Works with all types of Lipo & Lithium batteries for example 18650 bl5c bl5b
- Charge cellphone or power up your USB Gadgets
SKU: n/a - 433 Mhz, Arduino, Arduino Components, Modules, Power, Relays, Wireless
1 Channel Wireless 433Mhz Remote Control Relay Module 12V
433 Mhz, Arduino, Arduino Components, Modules, Power, Relays, Wireless1 Channel Wireless 433Mhz Remote Control Relay Module 12V
- Input Voltage: DC 12V
- Operating Voltage: 1 – 250 V
- RF Frequency: 433MHZ
- RF Working mode:Super heterodyne receiver
- Receiver Sensitivity: -107dBm
- Remote Control Distance: >100 meter(In open environment)
- Remote Control sold separately
- works with 433 mhz remote control with encoding type ev1527 pt2262 etc
- Decoding Way: MCU Software decoding
- Can store the number of remote control:32
SKU: n/a - Modules, Power, Voltage Converters
DC-DC 300W 9A Step Down Buck Converter CC-CV
- Color: as the pic shows
- Input voltage: 5-40V
- Output voltage: 1.2-35V (continuously adjustable)
- Output Current: 9A (if temperature exceeds 65°C please add cooling fan)
- Constant current range:0.2-9A ( adjustable )
- Output Power: Maximum power is about 300W (if temperature exceeds 65°C please add cooling fan)
- Size: Approx. 2.55*1.88*0.94inch / 6.5*4.8*2.4cm(Length*width*thickness)
SKU: n/a - Arduino, Arduino Components, Modules, Programmers, Tools
USB to Serial TTL Converter CH340G
- This is a USB 2.0 to TTL UART CH340/CH340G Module Serial Converter.
- Designed to be used for USB to TTL
- Built-in USB to RS232 Transfer chip.
- USB specification 2.0 compliant with full-speed 12Mbps.
- Standard USB type A male and TTL 5pin connector.
- Event character support Line break transmission.
- USB suspend states supported via SUSPEND pins.
- Temperature Range: -40degree to +85degree.
- Supports Windows 98SE, 2000, XP, Vista, Window7,8,10 Mac OS 9, Mac OS X Linux 2.40.
SKU: n/a - Modules, Power, Relays
Automatic Street Light On Off Photo Sensor Control Switch 220V 10A
- This Switch can be used to Automatically Turn ON & OFF Street Light & Garage Lights Based on Sun light Intensity
- For example It will turn on the lights when there is no sun light detected in the evening.
- It will automatically turn off the lights early in the morning when the sunlight detected.
- Power Saving & Energy Efficient Device
- This device Have some other uses as well.
- For example if you are using Wapda & Solar Power, You can cut off Wapda Load from UPS & Automatically Switch to Solar Energy
- When the Sunlight detected it means Solar Power is available (It kills Wapda Power & Switch to Solar Power)
- When the Sunlight not detected, that means the Solar Power is not available (It will Restore Wapda Power to UPS)
- It has built in Relay Module Which Supports 220V & 10A (Ideal Load for average Home UPS)
SKU: n/a - Arduino, Arduino Components, Modules, Programmers
CP2102 USB to Serial TTL Converter Micro USB
- Origional CP2102 IC Chip onboard
- Micro USB 6PIN TTL UART CP2102 Module
- On board Fuse for Short Circuit Protection
- DTR Pin for Auto Programming
- Designed to be used for USB to TTL Serial
- Built-in USB to RS232 Transfer chip
- Micro USB to TTL 6pin connector.
- 6pins for 3.3V, RST, TXD, RXD, GND & +5V.
- Temperature Range: -40degree to +85degree.
- Support: Windows, Linux & MAC
SKU: n/a - Modules, Power, Voltage Converters
0.9V 3V 5V to 5V 600MA USB Output Charger Module
- Input Voltage: 1-5V
- Output Voltage: 5.1-5.2V
- Output Current: Rated 600MA
- Efficiency:: Up to 96%
- Works with all types of Lipo & Lithium batteries for example 18650 bl5c bl5b
- Charge cellphone or power up your USB Gadgets
SKU: n/a - Modules, Power, Voltage Converters
XL4016 DC-DC 200W 8A Step Down Buck Converter
- Input voltage: DC 4-38V
- Output voltage: DC 1.25-36V
- Maximum current: 8A
- Maximum power: 200W
- Conversion efficiency: 95%
- Working Temperature: -45~+85℃
- Size: 6×3.7cm/2.36×1.46inch
- Voltage Regulating Mode: PWM Modulation
- Switching Frequency: 180KHz
SKU: n/a - Modules, Power, Voltage Converters
LTC1871 High Power 100W Digital Display Stepup Boost Module
The boost module uses advanced microcontroller and U.S. imports boost controller, it eliminates the need for a current sense resistor by utilizing the power mosfet’s on-resistance, thereby maximizing efficiency, up to 96.4%. Imported high-power low-resistance mos transistor, heavy current and high efficiency schottky, wider and thicker PCB traces, is a guarantee of high-power and low temperature rise. When the input and output voltage is greater than 20V, the module up to 128W output power.
SKU: n/a - Arduino, Arduino Components, Modules
TTL to RS485 MAX485 Converter
- on-board MAX-485 chip , is a tool for RS-485 communications , low-power , Slow-Rate Transceiver
- onboard 5.08 (mm) pitch 2P terminal for easy wiring RS-485 communication
- the chip has drawn all of the pins can be controlled by the microcontroller operation
- Working voltage : 5V
SKU: n/a - Arduino, Arduino Components, Modules, Sensors
Infrared Reflective Obstacle Avoidance Sensor
- Sensor module output port OUT can be directly connected with the microcontroller IO port.
- Can also directly drive a 5V relay; Connection: VCC-VCC; GND-GND; OUT-IO
- The Comparator with LM393, Stable.
- Can be used 3.3V-5V DC power supply module. When the power is turned on, the red power indicator light;
- VCC external 3.3V-5V voltage (can be directly connected with the 5v microcontroller or 3.3v single-chip)
- GND external GND
- OUT small board digital output interface (0 and 1)
SKU: n/a - Arduino Components, Modules, Power, Relays, Robotics
LED Display Automatic Cycle Delay Real Time Clock RTC Control Relay
Arduino Components, Modules, Power, Relays, RoboticsLED Display Automatic Cycle Delay Real Time Clock RTC Control Relay
- Operating voltage: 5.0V ~ 60V
- Support MicroUSB 5.0V Power Supply
- Trigger Source: Active-high (3.0V-24V),
- Output Capability: You can control the DC 30VDC 5A or 220VAC 10A device.
- Quiescent Current: 20mA; Operating Current: 50mA
- Life: more than 10 million times; Working temperature: -40-85
- This Module can be used to specifically Turn On / Turn Off an Electrical appliance on Specific Time for the specific duration
- This is Advanced Cyclic Timer Relay Module with Timer Clock function as well
SKU: n/a
