No products in the cart.
Arduino Components Price in Pakistan
Showing 49–72 of 129 results
- Arduino, Arduino Components, Arduino Shields, Modules
A4988 3D Printer Stepper Motor Driver Module
- Crossover-current protection
- Thermal shutdown circuitry
- 3.3 and 5 V compatible logic supply
- Thermal shutdown circuitry
- Ground Fault Circuit
- Load short-circuit protection
- Of five optional step mode: full, 1/2, 1/4, 1/8 and 1/16
SKU: n/a - Arduino, Arduino Components, Modules, Power, Relays, Sensors
W1209WK LED Digital Thermostat Temperature Control
Arduino, Arduino Components, Modules, Power, Relays, SensorsW1209WK LED Digital Thermostat Temperature Control
- Digital Thermostat
- Temperature Control Module can be used to control the temperature of anything (Solid or Liquid)
- Set the Specific Temperature You Want to Maintain.
- Module operates on 12v DC
- You can control DC or AC Appliances
- Used for Incubation
SKU: n/a - 433 Mhz, Arduino, Arduino Components, Modules, Wireless
SI4432 433mhz Wireless Transceiver Module
- Operating Frequency: 240Mhz – 930Mhz (customizable)
- Operating Voltage: 1.8V to 3.6V
- Current – Sleep mode : 1.0uA
- Current – Standby mode : 800nA
- Current – Receive mode : 18.5mA
- Current – Transmit mode @ +20dBm : 85mA
- Opeting Temperature: -20C to +70C
- Data rate – Maximum : 256kbps
- Transmit power : +20 dBm (Max)
- Receiver Sensetivity : -121dBm
- Range : upto 1.5km (depends upon several other parameters, hence not gauranteed)
- Module Header pin pitch: 0.05inch / 1.27mm
SKU: n/a - Arduino, Arduino Components, Modules, Programmers
USBASP USBISP Programmer for ATMEL AVR ATMega ATTiny
Arduino, Arduino Components, Modules, ProgrammersUSBASP USBISP Programmer for ATMEL AVR ATMega ATTiny
- Directly connected to USB port of PC
- Easy interfacing with Microcontroller
- Onboard ATMEGA8A chip for programming
- onboard 500ma overcurrent protection fuse
- 3.3v & 5v supply for target
- Support All AVR ASP chips
- Autospeed, automatic adaptive serial speed control.
- Reserved MOSI, MISO, RST, SCK, VCC, GND 6PIN Interface
SKU: n/a - Arduino, Arduino Components, Input, Modules, Power, Relays
2 Channel 5v Optically Isolated Relay Module
Arduino, Arduino Components, Input, Modules, Power, Relays2 Channel 5v Optically Isolated Relay Module
- Operating Voltage: 5v DC
- Relay contact capacity: 250v AC 10A, or 30v DC 10A
- Optically Isolated from Mains
- Relay output: normally open, normally closed
- Low level Trigger
- signal input voltage range: 0-5 v
- VCC is power supply to board. JD – VCC is relay power supply (Default: JD – VCC and VCC Jumper)
- Compatible with Arduino, PIC, AVR etc
SKU: n/a - 2.4 Ghz, Arduino, Arduino Components, Modules, Wireless
SPP-C Bluetooth Module
- Bluetooth V2.1 + EDR
- Bluetooth Class 2
- Built-in PCB radio frequency antenna
- Support UART interface
- 3.3V power supply
- Status indication LED: P12
- Used to indicate the status of the Bluetooth module, LED flashing mode and Bluetooth module status corresponding to the following table:
- Mode LED Displays the module status
- (800 ms-on, 800 ms-off) waiting for pairing
- Host interrupt indication: P05
- Used to indicate whether the host is interrupted or not, the connection status is high, and other states are low.
SKU: n/a - Arduino, Arduino Components, RFID, Wireless
125Khz RFID Tag Keychain
- Big coil, ABS material
- Strong magnetic induction
- 100% brand new and high quality
- Operation frequency: 125Khz
- Each token pre-programmed with unique ID which is printed on it
- Each comes with Key ring included
- Compatible with all RFID reader to gain access
- Card read distance: 0-10 centimetres
- Water resistant
SKU: n/a - Arduino, Arduino Components, Display, Modules
I2C Interface Plate for LCD Display Module
- I2C Address: 0x27
- Supply voltage: 5V
- Dimension: 41.5mm*19mm*15.3mm
- The Backlight and contrast is adjusted by Potentiometer
- Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable
- Compatible for 1602 16×2 2004 20×4 20×2 Character LCD Display
SKU: n/a - Arduino, Arduino Components, Modules, Sensors
Infrared Reflective Obstacle Avoidance Sensor
- Sensor module output port OUT can be directly connected with the microcontroller IO port.
- Can also directly drive a 5V relay; Connection: VCC-VCC; GND-GND; OUT-IO
- The Comparator with LM393, Stable.
- Can be used 3.3V-5V DC power supply module. When the power is turned on, the red power indicator light;
- VCC external 3.3V-5V voltage (can be directly connected with the 5v microcontroller or 3.3v single-chip)
- GND external GND
- OUT small board digital output interface (0 and 1)
SKU: n/a - 433 Mhz, Arduino, Arduino Components, Modules, Wireless
RX470 433Mhz Superheterodyne RF Receiver Module
433 Mhz, Arduino, Arduino Components, Modules, WirelessRX470 433Mhz Superheterodyne RF Receiver Module
- Product Model: RX470B-V02
- Superheterodyne Wireless Receiver Module
- Receiving UHF ASK Demodulators
- Support ASK and OOK Modulation.
- The receiver module has high sensitivity (-108dBm),
- Low-power performance, along with high dynamic range (greater than 60dB)
SKU: n/a - Arduino, Arduino Components, Sensors
Soil Moisture Detection Humidity Sensor Module
- Operating Voltage 3.3V-5V
- Module Dual Output mode , a simple digital output , analog output more accurate.
- With fixed bolt hole for easy installation
- Small PCB board size : 3cm * 1.6cm
- Power Indicator ( red ) and the digital switch output Indicator ( green )
- Using LM393 Comparator Chip , Stable
- VCC external 3.3V-5V
- GND GND External
- DO small board digital output interfaces ( 0 and 1 )
- AO small board analog output interface
SKU: n/a - Arduino, Arduino Components, Arduino Shields, Modules
3D Printer Engraving Machine A4988 Drive Extension CNC Shield For Arduino
Arduino, Arduino Components, Arduino Shields, Modules3D Printer Engraving Machine A4988 Drive Extension CNC Shield For Arduino
- This expansion board as a driver expansion board, can be used for engraving machines, 3D printers.
- It is a total of four slots, can drive four A4988 Stepper Motor.
- Each road Stepper Motors only need two IO ports.
- In other words, six IO ports can be well managed three stepper motors.
- Very Convenient to use.
SKU: n/a - 433 Mhz, Arduino, Arduino Components, Wireless
433Mhz RF Wireless Remote Control 2 Channel On Off
- This remote control only support the learning code (1527) of the receiver
- It can not clone other remote controls, it is only 1527 encoded remote control. (Fixed Code)
- Can only match the 1527 learning code receiver.
- Application: (Partial)
- Garage doors access control system
- Electronic gates access control system
- Electrical appliances control
- Vehicle central locking systems
- Car sunroofs control
- Heating systems control
SKU: n/a - Arduino, Arduino Components, Modules, Sensors
SW520D Tilt Sensor Module Module
- Using high-sensitivity switch SW 520D as the sensor.
- The module is equipped with fixed bolt hole for convenient installation.
- Using LM393 wide voltage comparator,clean signal,good waveform,strong driving ability with output of more than 15 mA.
- The working voltage of 3.3V to 5V.
- Small PCB size:3.2cm x 1.4cm.
- Digital output form: digital switch output (0 and 1).
SKU: n/a - 433 Mhz, Arduino, Arduino Components, Modules, Wireless
HC-12 SI4463 Wireless Serial Port Module 1000m
433 Mhz, Arduino, Arduino Components, Modules, WirelessHC-12 SI4463 Wireless Serial Port Module 1000m
- HC-12 SI4463 wireless microcontroller serial module
- 433mhz frequency with multiple channels
- 1000M extended range with antenna
- HC-12 is a wireless 433mhz transceiver module to communicate between microcontrollers through wireless link.
SKU: n/a
