No products in the cart.
- Arduino Components, Relays, Arduino, Modules, Power, Sensors
XH-W1219 LED Digital Thermostat Temperature Controller
Arduino Components, Relays, Arduino, Modules, Power, SensorsXH-W1219 LED Digital Thermostat Temperature Controller
- This is Universal Digital Thermostat
- Temperature Control Module can be used to control the temperature of anything (Solid or Liquid or Air)
- Set the Specific Temperature You Want to Maintain.
- Module operates on 12v DC
- You can control DC or AC Appliances
- Recommended for Incubation
SKU: n/a - Connectors, Components
USB 3.0 To 22Pin High Speed SATA Hard Disk Cable
- USB 3.0 Interface for High Speed Data Transmission
- 22Pin SATA is (7pin+15Pin).
- No Separate Power Supply Required
- Your desktop will have to support USB 3.0 (Also Backward Compatible with USB 2.0)
- The Cable supports 5V SATA 22 Pin HDD Adapter Cable.
- It supports with 2.5″ SATA HDD & SSD & DVD Players
- Plug & Play
SKU: n/a₨1,100 - IC, Components
TDA2030A 18W Mono Audio Amplifier Board
- Mono 18W Amplifier Circuit Design
- On-board speaker wire holder
- On-board 10K adjustable resistance, you can adjust the amplified volume
- Onboard power indicator
- The main board have pins leads, you can directly input audio signal (GND, IN)
- The working voltage: 6 ~ 12V
- Board size: 32 (mm) x24 (mm)
SKU: n/a - Connectors, Components
Dual Power eSATA USB 12V 5V Combo to 22Pin SATA USB Hard Disk Cable
- Power eSATA (eSATA+USB combo) to 22 Pin SATA cable.
- 22Pin SATA is (7pin+15Pin).
- Power Over eSATA connector.
- Your desktop will have to support this Power eSATA 5V and 12V.
- The Cable supports 5V/12V Power Over eSATA to SATA 22 Pin HDD Adapter Cable.
- It supports with 2.5″,3.5″ SATA HDD and 5.25″ Blueray Play, DVD Play and CD Rom with data transfer and power for 5V and 12V.
- Because of using 5V/12V Power Over eSATA connector.
- Cable length: 52cm/20.5inch
SKU: n/a - Arduino Components, Arduino, Modules
TTL To RS485 Industrial Converter with Lightening Protection
- Industrial Grade TTL to RS485
- On-board TTL to RS-485 converter chip
- Bi-Directional TVS transient Suppression Diode
- RS485 Lightening Protection design (Surge Protection)
- onboard 5.08 (mm) pitch 2P terminal for easy wiring RS-485 communication
- All of the pins can be controlled by the microcontroller operation (3.3 or 5v TTL)
- Working voltage : 3.0~30v DC
SKU: n/a - Bluetooth, Modules, Wireless, 2.4 Ghz
Universal Bluetooth Audio Receiver Kit for Sound System & Car
- Bluetooth Version: 4.1
- Frequency Range : 2.4GHz
- Profile: A2DP
- Transmission Range: Up to 10m / 33ft
- I/O 3.5mm female plug, Micro USB female port
- Power Supply: DC 5V (Micro USB)
- Charge Time: About 30 min
- Working Time: About 4h
SKU: n/a - Modules, Power, Voltage Converters
XL4016 DC-DC 200W 8A Step Down Buck Converter
- Input voltage: DC 4-38V
- Output voltage: DC 1.25-36V
- Maximum current: 8A
- Maximum power: 200W
- Conversion efficiency: 95%
- Working Temperature: -45~+85℃
- Size: 6×3.7cm/2.36×1.46inch
- Voltage Regulating Mode: PWM Modulation
- Switching Frequency: 180KHz
SKU: n/a - Arduino Components, Tools, Modules, Power
Digital Panel Voltmeter 0.36 LED Display 0-100V DC
- Type: 3-Wire Car Digital Voltmeter
- Material: Plastic
- Operating Voltage: DC 2.5-30V
- Operating Current: <20mA
- Measure Voltage: DC 0-100V
- Minimum Resolution: 0.1V / 0.01V
- Display: Red color, three digit, 0.36″
- Refresh Rate: About 200mS / times
SKU: n/a - Components, Modules
TPA3116D2 Digital HIFI Power Amplifier Board 2 X 120W
- Input Voltage 5-28V (more than 28V overvoltage protection)
- Support for low power 5V such as USB power supply
- Can also support high power 28V such as dual battery power supply
- Recommended power supply DC24V peak current 6A
- Output Maximum Power Up to 120W per channel
- Support 4 -8 Ohm speaker
SKU: n/a₨1,100₨1,300 - Modules, Sensors
XH-M452 LED Digital Thermostat Temperature Humidity Control Dual Output
- Digital Thermostat, Temperature Control Module can be used to control the Temperature & Humidity, Set the specific Temperature & Humidity you want to maintain.
- Power Supply :DC 12V
- Temperature Measurement Range:-40~120℃
- Humidity Range：0~100%RH
- Control Precision：0.1℃ 0.1%RH
- Test Probe：Integrated Sensor (Temperature & Humidity)
- Output: 2 Relays 10A
- Size:65*55*28mm
SKU: n/a₨2,500 - Input
Easycap Pro USB 2.0 Video Capture Card TV DVD VHS
- Support for All Formats: Record in DVD+/-R/RW, DVD+/-VR, and DVD-Video
- Support Output Formats: DV, AVI, MPEG, WMV, VCD, DVD
- Record from Digital TV Box, Dish Receivers, PTCL Smart TV, & All other Set Top Boxes with RCA Video Out
- One RCA Video In, Two RCA Stereo Audio In
SKU: n/a₨980₨1,250 - Relays, Modules, Power
XH-M603 Charge Controller Protection Module With LED Display
XH-M603 is a Charging Control Module 12-24V with Protection from Overcharging
- XH-M603 is ideal solution for Solar Panel & Battery
- Connect your Solar Panel or Charger on In+ & In-
- Connect Battery on BAT+ & BAT- (Lithium or Lead Acid)
- This Module protects your battery from Overcharging & Overheating
- It will extend the life of your battery
- This Module can operate on either 12V Single Battery or 24V Dual Battery
SKU: n/a - Arduino Components, Arduino, Wireless, 433 Mhz
433Mhz Wireless Remote Control 4 Channel
- Material: PVC
- RF Frequency: 433 Mhz
- Channel Supported: Four Channel
- Encoding Type: Learning Code(1527)
- Button: 4 Buttons
- Powered By: 27A 12V Battery  (Battery Included )
- Modulation System: ASK
- Operating Voltage:DC12V
- Operating Current:<25mA
- Transmitting Power: +13dbm
- Frequency Windage: ±0.2MHz
- Transmission Distance: 70m – 100m (Free Space)
- Color: White
SKU: n/a₨820₨1,000 - Orange Pi, Smart Boards
Orange Pi Zero H2+ Quad Core 512MB DDR3
- CPU: H2 Quad-Core Cortex-A7 H.265/HEVC 1080P
- GPU: Mali400MP2 GPU @600MHz, Supports OpenGL ES 2.0
- Memory: 512MB DDR3
- Onboard NIC: 100M/10M Ethernet RJ45
- Onboard Wifi: XR819, IEEE802.11 b/g/n
- Onboard Storage: Class 10 TF Card Slot, SPI Flash (Optional)
- Power: Micro USB
- USB 2.0: One USB 2.0 Host, One OTG 2.0 Host
- Low-level Peripherals: 26 Pins Header, Compatible with Raspberry Pi B+
- 13 Pins Header, with 2x USB, IR pin, Audio (MIC, AV)
- Supported OS: Android, Ubuntu, Debian, Armbian, OpenWRT etc
SKU: n/a₨1,850₨2,200 - Raspberry Pi, Smart Boards
Raspberry Pi 3 Model B with Wifi & Bluetooth
- Broadcom BCM2837 chipset running at 1.2 GHz
- 64-bit quad-core ARM Cortex-A53
- 802.11 b/g/n Wireless LAN (Wifi)
- Bluetooth 4.1 (Classic & Low Energy)
- Dual core Videocore IV® Multimedia co-processor
- 1 GB LPDDR2 memory
- Supports all the latest ARM GNU/Linux distributions and Windows 10 IoT
- MicroUSB connector for 2.5 A power supply
- 1 x 10/100 Ethernet port
- 1 x HDMI video/audio connector
- 1 x RCA video/audio connector
- 4 x USB 2.0 ports
- 40 GPIO pins
- Chip antenna
- DSI display connector
- MicroSD card slot
- Dimensions: 85 x 56 x 17 mm
SKU: n/a₨5,000 - Programmers
CH341A 24 25 Series EEPROM Flash BIOS USB Programmer
With this programmer you can program all sorts of
- Dish TV Receiver (25 series IC)
- Color TV set memory (24 series IC)
- LCD (24.25 series IC)
- Desktop motherboard (25 series IC)
- Notebook (25 series IC)
- Router (25 series IC)
- Card (25 series IC)
- DVD (25 series IC)
- Set-top boxes (25 series IC)
SKU: n/a
- Programmer Components, SPI Flash Memory, Components, Programmers
WINBOND W25Q32 Flash Memory Chip 32Mbit 4MB
Programmer Components, SPI Flash Memory, Components, ProgrammersWINBOND W25Q32 Flash Memory Chip 32Mbit 4MB
- Memory
- 32Megabits = 4Megabyte (MB)
- Voltage
- 2.7V to 3.6V
This is origional WINBOND 4MB SPI Memory chip.
Can be used in thousands of supported devices. for example routers, dish receivers, set top boxes, CPEs, lcds, laptops etc
SKU: n/a - Memory
- Programmer Components, SPI Flash Memory, Components, Programmers
MXIC MX25L3206E Flash Memory Chip 32Mbit 4MB
Programmer Components, SPI Flash Memory, Components, ProgrammersMXIC MX25L3206E Flash Memory Chip 32Mbit 4MB
- Memory
- 32Megabits = 4Megabyte (MB)
- Voltage
- 2.7V to 3.6V
This is MXIC 4MB SPI Memory Chip.
Can be used in thousands of supported devices. for example routers, dish receivers, set top boxes, CPEs, lcds, laptops etc
SKU: n/a - Memory
- Voltage Regulators, Components, Power, Voltage Converters
AMS1117 1.8v 800mA Low Dropout Voltage Regulator
Voltage Regulators, Components, Power, Voltage ConvertersAMS1117 1.8v 800mA Low Dropout Voltage Regulator
- Module property:Non-isolation Linear Regulator
- Rectification mode: None
- Input Voltage: 3V-9V
- Output Voltage: 1.8v
- Rated Output Current: 800ma Maximum (Not to be exceeded)
- Conversion Efficiency: >60%
- Switching Frequency: As Input
- Voltage regulation:± 2.5%
- Work temperature: -Minus 40 Degrees 85 Degrees
SKU: n/a - Programmers
CH341A 24 25 Series EEPROM Flash BIOS USB Programmer
With this programmer you can program all sorts of
- Dish TV Receiver (25 series IC)
- Color TV set memory (24 series IC)
- LCD (24.25 series IC)
- Desktop motherboard (25 series IC)
- Notebook (25 series IC)
- Router (25 series IC)
- Card (25 series IC)
- DVD (25 series IC)
- Set-top boxes (25 series IC)
SKU: n/a - Voltage Regulators, Components, Power, Voltage Converters
MIC5219 3.3v 5Pin Low Dropout Voltage Regulator
- Programmer Accessories, Programmers
SOIC8 SOP8 to DIP8 Socket Adapter 200mil Wide Body
- SOP8 to DIP8 IC Socket adapter
- Applications: Programmer,test socket,for SOP8 IC chips.
- Package:SOP8/SOIC8/SO8,lead pitch 1.27mm,Chip body width is 5.27mm
- Features:SOP8 to DIP8，baseplate lead to double row DIP 8P,lead pitch 2.54mm(100mil),width 1.52cm(600mil)
- Use for any Programmer.
- SMD Flash burn
SKU: n/a - Programmer Accessories, Programmers
SOIC8 SOP8 Flash Chip Adapter Clip for Programmer
- It can be used for the online in-circuit sop8 -dip8 adapter
- It is used for a sop8 chip programming that has been soldered on circuit board
- It can online program the sop8 chip , do not need take the chip of the circuit board
- So it can save people’s time
- Pin Format: SOIC8 / SOP8
SKU: n/a - Arduino Components, Relays, Arduino, Modules, Power, Sensors
W1209 LED Digital Thermostat Temperature Control
Arduino Components, Relays, Arduino, Modules, Power, SensorsW1209 LED Digital Thermostat Temperature Control
- This is Universal Digital Thermostat
- Temperature Control Module can be used to control the temperature of anything (Solid or Liquid or Air)
- Set the Specific Temperature You Want to Maintain.
- Module operates on 12v DC
- You can control DC or AC Appliances
- Recommended for Incubation
SKU: n/a - Voltage Regulators, Components, Power, Voltage Converters
AMS1117 3.3v 800mA Low Dropout Voltage Regulator
Voltage Regulators, Components, Power, Voltage ConvertersAMS1117 3.3v 800mA Low Dropout Voltage Regulator
- Module property:Non-isolation Linear Regulator
- Rectification mode: None
- Input Voltage: 4V-8V
- Output Voltage: 3.3v
- Rated Output Current: 800ma Maximum (Not to be exceeded)
- Conversion Efficiency: >60%
- Switching Frequency: As Input
- Voltage regulation:± 2.5%
SKU: n/a - Arduino Components, Connectors, Jumpers, Arduino, Components
2.54mm Pitch Jumper Wire for Prototyping
- Programmer Components, SPI Flash Memory, Components, Programmers
WINBOND W25Q64 Flash Memory Chip 64Mbit 8MB
Programmer Components, SPI Flash Memory, Components, ProgrammersWINBOND W25Q64 Flash Memory Chip 64Mbit 8MB
- Memory
- 64Megabits = 8Megabyte (MB)
- Voltage
- 2.7V to 3.6V
This is Original WINBOND 8MB SPI Memory chip.
Can be used in thousands of supported devices. for example routers, dish receivers, set top boxes, CPEs, lcds, laptops etc
SKU: n/a - Memory
- Programmer Components, SPI Flash Memory, Components, Programmers
cFeon Q32B Flash Memory Chip 32Mbit 4MB
Programmer Components, SPI Flash Memory, Components, ProgrammerscFeon Q32B Flash Memory Chip 32Mbit 4MB
- Single power supply operation
- Full voltage range: 2.7-3.6 volt
- Serial Interface Architecture
- SPI Compatible: Mode 0 and Mode 3
- 32 M-bit Serial Flash
- 32 M-bit/4096 K-byte/16384 pages
- 256 bytes per programmable page
- Standard, Dual or Quad SPI
- Standard SPI: CLK, CS#, DI, DO, WP#
- Dual SPI: CLK, CS#, DQ0, DQ1, WP#
- Quad SPI: CLK, CS#, DQ0, DQ1, DQ2, DQ3
SKU: n/a - Single power supply operation
- Components, Modules
PAM8610 Digital Amplifier Board 15W x 2
- 2 * 15W D Class
- Supply voltage: DC 7V-15V
- Output power: 10w + 10w (8 load)
- Efficiency: 90%
- Shutdown Current: 4uA
- Quiescent current; 20mA
- SNR: 86%
- Total harmonic distortion: 5W / 1KHz / 8 —- 0.1%
- Frequency range: 20Hz-20KHz
- Input impedance: 15K
- Output Impedance: 4-8
- Amplifier board size: 30mm * 25mm * 2.5mm
SKU: n/a - Programmer Components, SPI Flash Memory, Components, Programmers
GigaDevice GD25Q32 Flash Memory Chip 32Mbit 4MB
Programmer Components, SPI Flash Memory, Components, ProgrammersGigaDevice GD25Q32 Flash Memory Chip 32Mbit 4MB
- Memory
- 32Megabits = 4Megabyte (MB)
- Voltage
- 2.7V to 3.6V
This is origional GigaDevice GD25Q32 4MB SPI Memory chip.
Can be used in thousands of supported devices. for example routers, dish receivers, set top boxes, CPEs, lcds, laptops etc
SKU: n/a - Memory
- Voltage Regulators, Components, Power, Voltage Converters
AMS1117 5v 800mA Low Dropout Voltage Regulator
Voltage Regulators, Components, Power, Voltage ConvertersAMS1117 5v 800mA Low Dropout Voltage Regulator
- Module property:Non-isolation Linear Regulator
- Rectification mode: None
- Input Voltage: 6V-12V
- Output Voltage: 5v
- Rated Output Current: 800ma Maximum (Not to be exceeded)
- Conversion Efficiency: >60%
- Switching Frequency: As Input
- Voltage regulation:± 2.5%
- Work temperature: -Minus 40 Degrees 85 Degrees
SKU: n/a - Arduino Components, Arduino, Modules, Wireless, GSM
SIM800L GPRS GSM Module Quad Band
- Chip: SIM800L
- Voltage: 3.7-4.2V (works on 5v)
- Voice Support, directly attach microphone and speaker
- Best for SMS CALL GPRS
- Original Product
- Support networks: Global quad-band network
- Module size: 2.5cmx2.3cm
SKU: n/a₨900₨1,000
- Modules, Power, Voltage Converters
0.9V 3V 5V to 5V 600MA USB Output Charger Module
- Input Voltage: Â 1-5V
- Output Voltage: Â 5.1-5.2V
- Output Current: Â Rated 600MA
- Efficiency:: Â Up to 96%
- Works with all types of Lipo & Lithium batteries for example 18650 bl5c bl5b
- Charge cellphone or power up your USB Gadgets
SKU: n/a₨70₨90 - Arduino Components, Display, Robotics, Arduino, Modules
2004 20×4 Character LCD Display Module
- Interface: I2c
- I2C Address: 0x20
- Back lit (Green with Black Character Color) (Blue with White Character Color)
- Fully Assembled and Tested Serial LCD 20×4 Module
- Display Format: 20 Characters x 4 lines
- Supply voltage: 5V
- The module can be easily interfaced with a MCU
- The module is a low-power consumption character LCD Module with a built-in controller
- Size: approx. 9.8cm x 6cm x 1.2cm
SKU: n/a - Arduino Components, Arduino, Modules, Wireless, 433 Mhz
433Mhz RF Receiver Learning Code Decoder Module
Arduino Components, Arduino, Modules, Wireless, 433 Mhz433Mhz RF Receiver Learning Code Decoder Module
- Button usage (set the mode and starts pairing process):
- Press the button 8 times to clear previously stored codes
- Then press again onece, twice, or three time according to your configuration
- Press once: Inching mode (Momentary Mode)
- Press twice: self-Lock Mode (Toggle-Mode of the 4 Channels)
- Press three times: interlocked mode (selected channel active and be cleared, if another channel becomes active)
SKU: n/a₨350₨450 - Arduino Components, Arduino, Wireless, 433 Mhz
433Mhz RF Wireless Remote Control 4 Channel
- Clone your existing 433mhz Remote Control Key FOB
- Working voltage: DC 12V (built-in battery)
- Compatible with Arduino & 433mhz receiver
- Operating Current: <25ma
- Transmitting frequency: 433Mhz
- Key number: 4 Key (4 Channel)
- Emission Distance: 70-100m (Open area)
- Encoding type: fixed code (1527)
- Color: Silver Black
- Case material: Metal and PVC
SKU: n/a₨800₨900 - Arduino Components, Arduino, Wireless, 433 Mhz
433Mhz Wireless Remote Control 4 Channel
- Material: PVC
- RF Frequency: 433 Mhz
- Channel Supported: Four Channel
- Encoding Type: Learning Code(1527)
- Button: 4 Buttons
- Powered By: 27A 12V Battery  (Battery Included )
- Modulation System: ASK
- Operating Voltage:DC12V
- Operating Current:<25mA
- Transmitting Power: +13dbm
- Frequency Windage: ±0.2MHz
- Transmission Distance: 70m – 100m (Free Space)
- Color: White
SKU: n/a₨820₨1,000 - Arduino Components, Arduino, Wireless, 433 Mhz
433Mhz Wireless Remote Control 4 Channel Black
- Clone your existing 433mhz Remote Control Key FOB
- Working voltage: DC 12V (built-in button battery)
- Compatible with Arduino & 433mhz receiver
- Operating Current: <25ma
- Transmitting frequency: 433Mhz
- Key number: 4 Key (4 Channel)
- Emission Distance: 70-100m (Open area)
- Encoding type: fixed code (1527)
- Color: Black
- Case material: Metal and PVC
SKU: n/a₨800₨900 - Arduino Components, Arduino Shields, Arduino, Modules
A4988 3D Printer Stepper Motor Driver Module
- Crossover-current protection
- Thermal shutdown circuitry
- 3.3 and 5 V compatible logic supply
- Thermal shutdown circuitry
- Ground Fault Circuit
- Load short-circuit protection
- Of five optional step mode: full, 1/2, 1/4, 1/8 and 1/16
SKU: n/a₨220₨250 - Arduino Components, Arduino, Modules, Wireless, 2.4 Ghz
AT-09 4.0 Bluetooth Module CC2540 CC2541
- Ultra-low standby power consumption 90uA ~ 400uA
- Super-long connection distance of 100 feet / 60 meters
- ultra-fast reaction rate of 0.4 seconds
- Andrews, Apple, PC, MAC all-purpose.
- send and receive no byte limit, up to 3K Bytes / second
- do not need to do MFI
- IOS system perfect support.
- Android 4.3 system perfect support.
SKU: n/a₨500₨800 - Arduino Components, Arduino Shields, Arduino, Modules
DRV8825 3D Printer Stepper Motor Driver Module
- It is upgrade of A4988, 4-layer PCB for improved heat dissipation and decrease chip resistance
- Suitable for driving below 8.2V ~ 45V 2.5A stepper motor
- Six different stepping resolutions: full, half, 1 / 4,1 / 8,1 / 16,1 / 32.
- A simple steps and direction control interface.
- Adjustable potentiometer can adjust the maximum output current, resulting in higher step rate.
- Automatic current decay mode detection / selection.
- Thermal shutdown circuit, undervoltage lockout, crossover current protection.
SKU: n/a₨250₨300 - Input
Easycap Pro USB 2.0 Video Capture Card TV DVD VHS
- Support for All Formats: Record in DVD+/-R/RW, DVD+/-VR, and DVD-Video
- Support Output Formats: DV, AVI, MPEG, WMV, VCD, DVD
- Record from Digital TV Box, Dish Receivers, PTCL Smart TV, & All other Set Top Boxes with RCA Video Out
- One RCA Video In, Two RCA Stereo Audio In
SKU: n/a₨980₨1,250 - Inverters, Modules, Power
EGS002 EG8010 + IR2113 Pure Sine Wave Inverter SPWM Module
- 5V single power supply
- 4 pin set of pure sine wave output frequency:
- 50Hz pure sine wave of fixed frequency of 60Hz pure sine wave of fixed frequency 0-100Hz
- pure sine wave frequency adjustable 0-400Hz pure sine wave frequency adjustable
- Unipolar and bipolar modulation
- 300nS dead time 500nS dead time 1.0uS dead time 1.5uS dead time
- External 12MHz crystal oscillator
- PWM carrier frequency 23.4KHz
- Voltage, current, real time temperature feedback
- Overvoltage, undervoltage, overcurrent and overheating protection
- Soft-start mode pin setting the response time of 1S
- Serial communication to set the output voltage, frequency and other parameters
- External Serial LCD Module 1602 displays the inverter
- voltage, frequency, temperature and current information
SKU: n/a₨1,300₨1,600 - Arduino Components, Espressif, Arduino, Modules, Wireless, 2.4 Ghz
ESP8266 07 Wifi Module
- Improve the peripheral circuit
- Enhanced impedance matching
- Signal output is better, whether it is stable or anti jamming ability
- IPEX Connector For External Antenna
- PCB antenna after professional laboratory testing, perfect matching, after ROHS certification, have been greatly improved!
- The enhanced version is fully compatible with the firmware before the ESP-12, based on the SPI and the new six IO port
- Development is more convenient, more widely used!
- Node MCU Compatible
- Arduino IDE Compatible
SKU: n/a₨400₨500 - Arduino Components, Arduino, Modules, Sensors
GY-291 ADXL345 Digital 3 Axis Digital Gravity Sensor
- GY-291 ADXL345 Digital 3 Axis Digital Gravity Sensor Module for Arduino & PIC
- ADXL345 is well suited for mobile device applications. It can tilt sensing applications
- Measures the static acceleration of gravity, you can measure motion or shock resulting from moving
- State acceleration. Its high resolution (3.9mg / LSB), capable of measuring less than 1.0 °
- Tilt angle change.
SKU: n/a₨200₨250 - Arduino Components, Arduino, Modules, Sensors
KY-026 IR Flame Sensor Fire Detection Module
- High sensitivity IR receiver
- Extremely sensitive to wave between 760-1100nm
- Power supply indicator lamp
- Comparator output indicator lamp
- AO, real-time thermister voltage signal output
- DO, high / low electric level signal output
- Analog quantity output
- Threshold rollover electric level output
- Threshold adjusted by potentiometer
- Detection Angle Range: About 60 degrees
- Power Supply: 0-15 V DC
- Hole Inner Diameter: Approx. 3mm
- Size (L x W): Approx. 36 x 16mm
SKU: n/a₨120₨190 - Modules, Power, Voltage Converters
LTC1871 High Power 100W Digital Display Stepup Boost Module
The boost module uses advanced microcontroller and U.S. imports boost controller, it eliminates the need for a current sense resistor by utilizing the power mosfet’s on-resistance, thereby maximizing efficiency, up to 96.4%. Imported high-power low-resistance mos transistor, heavy current and high efficiency schottky, wider and thicker PCB traces, is a guarantee of high-power and low temperature rise. When the input and output voltage is greater than 20V, the module up to 128W output power.
SKU: n/a₨550₨650 - Modules, Power, Voltage Converters
LTC3780 DC-DC 10A Buck Boost Step UP Down
- The power supply is a kind of high-efficiency voltage automatically regulator.
- Whatever is the input voltage value,the output voltage can be maintained constant.
- For example,set the output to 12V, then the variation of the input voltage in the range of 5-32V,
- This module has a perfect protection function, and can be widely used in notebook power,
- vehicle power supply, solar charge etc..
SKU: n/a₨2,200₨2,500 - Arduino Components, Arduino, Modules, Wireless, GSM
M590E GPRS GSM Module Dual Band DIY
M590E GPRS GSM Module Dual Band (UnSoldered)
- This is UnSoldered (do it yourself) KIT
- Chip: M590E
- Voltage: 5v
- Best for SMS GPRS
- Support networks: GSM 900 & GSM 1800 Network
- Module size:Â 50mm*50mm
- TTL serial port for serial port, you can link directly to the microcontroller. No need MAX232
- Power module automatically boot on home network
- Onboard status LED.
SKU: n/a₨350₨500 - Arduino Components, Arduino, Modules
Micro USB Plugable Programing Board for Atmel Attiny Microcontrollers
Arduino Components, Arduino, ModulesMicro USB Plugable Programing Board for Atmel Attiny Microcontrollers
- Pluggable Development Board for Atmel Attiny Microcontrollers.
- Programming Editor
- Micro USB connection
- Supported Chips.
- ATtiny13A
- ATtiny25
- ATtiny45
- ATtiny85
SKU: n/a₨150₨190 - Arduino Components, Arduino, Modules, Sensors
Microphone Sensor Sound Detection Module
- Operating Voltage: 3v to 5.5v
- Sound Detection Module has two output
- AO, analog output, real-time output voltage signal of the microphone
- DO, when the sound intensity reaches a certain threshold, the output high and low signal
SKU: n/a₨150₨180
